Printable seat plate for T-LoVendo AM-SOC26 office chair

Parametric OpenSCAD model with gas lift taper socket, backrest bar
channel with M8 through-bolts, lever with drop-in pivot, shims and a
taper fit gauge.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01QM7McqDDPqszyN8ojQxVjk
This commit is contained in:
BartandClaude Opus 5.5 committed 2026-10-31 23:42:26 +01:00
commit 2edb878317
11 files changed
+438

No files matched your search

+2
View File
@@ -0,0 +1,2 @@
*.stl
*.3mf
+170
View File
@@ -0,0 +1,170 @@
# Office chair seat plate (3D printable)
A printable replacement for the seat mechanism plate of a **T-LoVendo AM-SOC26** office
chair (it arrived without one). The plate screws to the underside of the seat with the
4 original M6 screws, takes the gas lift taper, clamps the backrest bar with the
original knob, and carries a lever that presses the gas lift release pin.
It is a single parametric [OpenSCAD](https://openscad.org) file: `seat_plate.scad`.
Every dimension is a named parameter, so it can be adapted to similar chairs.
![Assembly, seen from below](images/assembly.png)
| Underside | Seat side |
|---|---|
| ![Plate from below](images/plate_below.png) | ![Plate seat side](images/plate_seatside.png) |
> **Safety.** This replaces a steel part that you sit on. Printed plastic is weaker,
> creeps under constant load and can fail without much warning (especially PLA).
> Test it carefully (see [Testing](#testing)) and inspect it regularly for whitening,
> cracks or a growing gap at the back of the plate.
## Parts
Export each part by setting `part`:
| `part` | What | Qty | Print orientation |
|---|---|---|---|
| `plate` | The seat plate | 1 | Seat face down (already rotated) |
| `lever` | Gas lift lever | 1 | Flat |
| `pivot` | Lever pin (8 mm) + 2 keepers | 1 set | As exported (pin lies on a small flat) |
| `shims` | 3 mm spacers for the curved seat | 4 | Flat |
| `gauge` | Taper fit test piece | 1 | As exported, same settings as the plate |
| `assembly` | Preview only | – | – |
```sh
for p in plate lever pivot shims gauge; do
openscad -o $p.stl -D "part=\"$p\"" seat_plate.scad
done
```
The STLs are not in this repo; generate them from the source.
### Hardware
- 4× M6×20 screws (the chair's originals) with 4× large M8 washers
(23.7 mm OD, 8.5 mm ID, 2 mm thick) under the heads
- 2× M8×35 socket head bolts, 2× M8 nylon lock nuts, 2× M8 washers (same washers as above)
- Optional: an 8 mm steel rod cut to 30 mm instead of the printed pin
## How it works
### Gas lift socket
A 50 mm long tapered bore that matches the gas cylinder's taper
(26.5 → 28 mm over 53 mm). Above it is a 3 mm **stop ring** with an 18 mm hole:
- The release pin pokes through the hole into the lever pocket.
- Normally there is a 1 mm gap between the cylinder top and the ring; the taper does
all the gripping. The ring only catches the cylinder if the plate creeps further down
the taper. This keeps the release pin at the height the lever expects and limits how
far the taper can wedge into (and split) the boss.
Assemble the taper **dry**, without grease.
### Backrest bar channel
The 35×16 mm stadium-section bar slides into a channel that is open towards the seat
board. The bar's 23 mm flange (around the knob thread) presses against the seat board;
the small 12.5 mm boss on the knob side runs in a slot in the channel floor. 76.5 mm
of the bar is inside the channel (of the ~80 mm available before its ribbed cover).
This is the most heavily loaded part. Leaning back pushes the bar down on the rear
edge of the channel and up against the seat board at its front end, a couple of
roughly 3 kN in a hard lean. To make this stronger:
- The channel walls are 20 mm thick, the floor 15 mm.
- An **M8 bolt runs vertically through each wall** near the rear end. The lock nut sits
in a hex pocket on the seat face (it can't turn and the seat board covers it); the
bolt goes in from below with a washer under the head. This clamps the printed layers
together where leaning back tries to pull them apart. With a 2 mm washer the bolt tip
ends 0.8 mm below the seat face, so **don't leave the washer out**.
![Section through the bar channel at the M8 bolts](images/section_bar_bolts.png)
### Lever
A first-class lever: pulling the handle up pushes the inner end down onto the
release pin. At rest the inner end lies against the seat board, 1.5 mm above the pin;
nub travel is limited to 7.5 mm by the pocket floor.
![Lever](images/lever.png)
The lever pivots on an 8 mm pin that drops into **open-top slots** in the housing walls.
Pulling the handle pushes the pin *up*, so two printed **keepers** fill the slots above
the pin ends; once the plate is mounted they are backed by the seat board.
| Lever in its pocket | Section through the pivot |
|---|---|
| ![Section in the lever plane](images/section_lever.png) | ![Section through the pivot](images/section_pivot.png) |
![Pivot pin and keepers](images/pivot.png)
### Seat screws
The seat underside is curved: about 3 mm higher at the screw holes than at the centre.
The 4 printed shims fill that gap. The screw counterbores are 25 mm wide for the large
washers, with 6 mm of plastic under them. Stack per screw: 2 mm washer + 6 mm plastic
+ 3 mm shim, which leaves about 9 mm of an M6×20 in the seat's T-nuts. Check that each
screw goes in at least 8–9 turns by hand before tightening.
## Calibrating the taper fit
Printed holes come out undersized, and this taper is shallow: **every 0.1 mm of
diameter moves the seating height by about 3.5 mm**. Tune `socket_clear` with the gauge
before printing the plate:
1. Print `gauge` with exactly the settings, filament and orientation you'll use for the plate.
2. Push it on the cylinder firmly by hand (twist it to get it off again).
3. Target: about 3 mm of shiny taper visible below the gauge, and about 4 mm from the top
of the gauge down to the cylinder top.
4. If it sits X mm too high, increase `socket_clear` by roughly X / 35 mm. If it
rattles or the cylinder touches the stop ring, decrease it.
Err slightly on the tight side: body weight seats it further, and the plate's thick
boss stretches less than the thin gauge. Too loose means the cylinder rests on the
stop ring and wobbles.
Here, `socket_clear = 0.2` sat 15.5 mm high; the printed plate uses **0.5**.
## Printing
- PLA works but is brittle and creeps. PETG, ABS/ASA (enclosure needed) or PA/PC are
tougher choices.
- Use many walls (8–10) so the channel walls print as solid perimeters, and a 100 %
infill modifier around the bar channel. Print hot enough for good layer bonding.
## Assembly
1. Press the two M8 lock nuts into the hex pockets on the seat face.
2. Insert the M8 bolts from below, with a washer under each head, and snug them up.
3. Slide the pin through the lever, drop the lever into its pocket with the pin ends in
the slots, and press the keepers in on top (a bit of tape holds them while flipping).
4. Place the shims, put the plate on the seat and fit the M6×20 screws with the large washers.
5. Tighten the M8 bolts, insert the backrest bar and fit the knob.
6. Set the seat onto the gas cylinder (taper dry) and sit down to seat it.
## Testing
Before trusting it, load the backrest gradually: put a bathroom scale between your hand
and the top of the backrest and push to about twice your normal lean. Look and listen
for whitening, creaking, or a gap opening at the back of the plate. Re-check the knob
and the screws after the first days, since the plastic settles.
## Known deviations on the printed chair
The measurements are hand measured. On the build in this repo:
- One of the four outer screw holes had to be opened up about 1 mm with a drill (the hole
pattern on the seat is probably not a perfect rectangle).
- The hole for the backrest knob had to be drilled further back, so `knob_from_rear_holes`
is too large for this chair.
The model has **not** been updated for these; measure your own chair and check the hole
positions before printing.
## Coordinates (for editing)
Origin at the centre of the 4-screw pattern on the seat underside, +y towards the front,
+x to the sitter's right, z = 0 at the seat board; the plate hangs at z < 0.
`lever_side = -1` mirrors the lever to the left side.
Binary file not shown.

After

Width:  |  Height:  |  Size: 38 KiB

BIN
View File
Binary file not shown.

After

Width:  |  Height:  |  Size: 5.6 KiB

BIN
View File
Binary file not shown.

After

Width:  |  Height:  |  Size: 23 KiB

Binary file not shown.

After

Width:  |  Height:  |  Size: 37 KiB

Binary file not shown.

After

Width:  |  Height:  |  Size: 31 KiB

Binary file not shown.

After

Width:  |  Height:  |  Size: 4.4 KiB

Binary file not shown.

After

Width:  |  Height:  |  Size: 6.4 KiB

Binary file not shown.

After

Width:  |  Height:  |  Size: 4.5 KiB

+266
View File
@@ -0,0 +1,266 @@
// Seat plate for T-LoVendo AM-SOC26 office chair (printed replacement)
//
// Chair coordinates: origin = centre of the 4-screw pattern on the seat underside,
// +y = front, +x = sitter's right, z = 0 is the seat board, the plate hangs at z < 0.
// Exported parts are re-oriented for printing.
part = "assembly"; // [assembly, plate, lever, pivot, gauge, shims]
lever_side = 1; // 1 = lever on sitter's right, -1 = left
$fn = 96;
e = 0.01;
/* ---------- measured ---------- */
hole_dy = 135; // front-back hole spacing
hole_dx_front = 124;
hole_dx_rear = 128;
cone_from_front_holes = 62; // front hole line -> gas cylinder axis
knob_from_rear_holes = 17; // rear hole line -> backrest knob axis (forward)
cone_d_top = 26.5; // measured just below the rounded top edge
cone_d_bot = 28.0;
cone_len = 53; // taper length between those two diameters
cone_round = 2; // rounded top edge above the d_top point
button_h = 7.3; // orange release pin above cylinder top
bar_w = 35; // backrest bar, stadium section
bar_t = 16;
bar_boss_seat = 2.5; // 23 mm flange, faces the seat board (channel is open there)
bar_boss_knob = 1.0; // small boss around the thread, knob side
bar_hole_from_end = 19;
knob_stud_d = 10; // M10
knob_stud_len = 25;
knob_d = 60;
seat_sag = 3; // seat underside is curved: this much higher at the screw holes than at the centre
boss_groove_w = 14; // slide slot for the knob-side boss (12.5 measured) + clearance
knob_engage = 11; // thread engagement wanted in the bar (threaded through)
bar_insert_max = 80; // bar length that fits in before the ribbed cover
/* ---------- design ---------- */
screw_d = 6.6; // M6 clearance
head_cb_d = 25; // counterbore for screw head + large M8 washer (23.7 OD)
under_head = 6; // material under the washer; with 3 mm shim + 2 mm washer an M6x20 grips 9 mm
plate_t = 12;
plate_r = 14; // outline radius around each hole
socket_clear = 0.5; // added to taper diameter; tune with the gauge part (0.2 sat 15.5 mm high)
shoulder_t = 3; // stop ring above the cylinder top
shoulder_gap = 1; // nominal gap cylinder top -> stop ring
shoulder_hole = 18;
shoulder_top = -18; // = floor of lever pocket above the socket
engage = 50; // taper length gripped by the socket
boss_r = 24;
clamp_groove = false; // seat for an optional steel hose clamp (40-60 mm); shortens the ribs
clamp_w = 12; // groove at the socket mouth; ribs start above it
bar_clear = 0.3;
floor_t = 15; // under the backrest bar
wall = 20; // beside the backrest bar
keel_back = -108; // how far the bar channel extends rearward
bolt_len = 35; // M8x35 socket head, up through each wall from below
bolt_hole = 8.5;
nut_af = 13; // M8 nylon lock nut, captive at the seat face
nut_h = 8;
washer_t = 2; // M8 washer under the bolt head (23.7 OD, 2 mm)
bolt_from_back = 10;
lever_w = 12; // lever thickness (y)
lever_clear = 1; // per side
pivot_x = 40;
pivot_z = -8;
pin_d = 8; // printed pin (or 8 mm steel rod), drops into open-top slots
pin_clear = 0.4; // slot width over pin_d
rest_gap = 1.5; // lever nub above release pin at rest (nominal fit)
travel = 7.5; // max nub travel before lever body bottoms out
nub_w = 8;
handle_drop = 42; // handle runs this far below the seat board
handle_end = 195; // handle tip, from seat centre
/* ---------- derived ---------- */
fy = hole_dy/2;
holes = [[ hole_dx_front/2, fy], [-hole_dx_front/2, fy],
[ hole_dx_rear/2, -fy], [-hole_dx_rear/2, -fy]];
cone_y = fy - cone_from_front_holes;
knob_y = -fy + knob_from_rear_holes;
bar_end_y = knob_y + bar_hole_from_end;
shoulder_bot = shoulder_top - shoulder_t;
cone_top_z = shoulder_bot - shoulder_gap; // nominal seated cylinder top
dtop_z = cone_top_z - cone_round;
bore_bot = dtop_z - engage;
function bore_d(z) = cone_d_top + (dtop_z - z) * (cone_d_bot - cone_d_top) / cone_len + socket_clear;
chan_floor = -(bar_t + bar_boss_seat + bar_clear);
keel_bot = chan_floor - floor_t;
keel_hw = bar_w/2 + bar_clear + wall;
groove_d = bar_boss_knob + 0.5;
knob_cb_z = chan_floor - bar_boss_knob + knob_engage - knob_stud_len;
rib_bot = bore_bot + (clamp_groove ? clamp_w + 5 : 8);
edge_x = max(hole_dx_front, hole_dx_rear)/2 + plate_r - 1;
cav_hw = lever_w/2 + lever_clear;
house_hw = cav_hw + 8;
house_bot = -26;
hub_r = -pivot_z - 0.5; // lever hub just clears the seat board
slot_w = pin_d + pin_clear;
keeper_h = -pivot_z - pin_d/2 - 0.1; // fills the slot above the pin, seat board on top
bolt_x = bar_w/2 + bar_clear + wall/2;
bolt_y = keel_back + bolt_from_back;
bolt_tip = keel_bot - washer_t + bolt_len;
button_nom = cone_top_z + button_h;
body_bot = shoulder_top + travel;
nub_bot = button_nom + rest_gap;
echo(str("Cylinder axis ", cone_y, " mm in front of pattern centre; knob at y=", knob_y));
echo(str("Plate depth below seat: ", -bore_bot, " mm; material under knob: ", (chan_floor - groove_d) - max(knob_cb_z, keel_bot), " mm; knob thread engagement: ", keel_bot + knob_stud_len - (chan_floor - bar_boss_knob), " mm"));
echo(str("Knob rim to socket boss: ", (cone_y - boss_r) - (knob_y + knob_d/2), " mm"));
echo(str("Bar inserted ", bar_end_y - keel_back, " of ", bar_insert_max, " mm"));
echo(str("M8 bolt tip ", -bolt_tip, " mm below seat face, through ", bolt_tip + nut_h + 0.3, " of ", nut_h, " mm nut; head to knob rim ", norm([bolt_x, bolt_y - knob_y]) - knob_d/2 - 8, " mm"));
echo(str("Gauge: expect ", cone_len + cone_round - (cone_top_z - bore_bot), " mm of shiny taper showing below the gauge"));
/* ---------- plate ---------- */
module rib(a, len, d_end, t) {
translate([0, cone_y, 0]) rotate(a) hull() {
translate([0, -t/2, rib_bot]) cube([boss_r - 1, t, -rib_bot]);
translate([len - 1, -t/2, -d_end]) cube([1, t, d_end]);
}
}
module plate_solid() {
// base plate
translate([0, 0, -plate_t]) linear_extrude(plate_t)
hull() for (h = holes) translate(h) circle(plate_r);
// keel carrying the backrest bar, running into the socket boss
translate([-keel_hw, keel_back, keel_bot]) cube([2*keel_hw, cone_y - keel_back, -keel_bot]);
// socket boss
translate([0, cone_y, bore_bot]) cylinder(r = boss_r, h = -bore_bot);
// lever housing
translate([0, cone_y - house_hw, house_bot]) mirror_x() cube([edge_x, 2*house_hw, -house_bot]);
// gussets
rib(90, fy + plate_r - cone_y - 2, plate_t, 12);
rib(lever_side > 0 ? 180 : 0, edge_x, plate_t, 12);
rib(lever_side > 0 ? 0 : 180, edge_x, -house_bot, 16);
for (h = holes) {
v = h - [0, cone_y];
rib(atan2(v[1], v[0]), norm(v) - plate_r, plate_t, 8);
}
}
module mirror_x() { if (lever_side > 0) children(); else mirror([1, 0, 0]) children(); }
module stadium(w, t, len) { // along +y, flat bottom face at z = 0
r = t/2;
hull() for (sx = [-1, 1]) translate([sx*(w/2 - r), 0, r]) rotate([-90, 0, 0]) cylinder(r = r, h = len);
}
module plate() {
difference() {
plate_solid();
// screw holes, counterbored from below
for (h = holes) translate(h) {
translate([0, 0, -50]) cylinder(d = screw_d, h = 51);
translate([0, 0, -100]) cylinder(d = head_cb_d, h = 100 - under_head);
}
// tapered socket + entry chamfer
translate([0, cone_y, 0]) {
translate([0, 0, bore_bot - e]) cylinder(d1 = bore_d(bore_bot), d2 = bore_d(shoulder_bot), h = shoulder_bot - bore_bot + e);
translate([0, 0, bore_bot - e]) cylinder(d1 = bore_d(bore_bot) + 3, d2 = bore_d(bore_bot), h = 1.5);
translate([0, 0, shoulder_bot - e]) cylinder(d = shoulder_hole, h = 10);
if (clamp_groove) translate([0, 0, bore_bot + 3]) difference() {
cylinder(r = boss_r + 1, h = clamp_w);
translate([0, 0, -e]) cylinder(r1 = boss_r, r2 = boss_r - 1, h = 1 + e);
translate([0, 0, 1]) cylinder(r = boss_r - 1, h = clamp_w - 2);
translate([0, 0, clamp_w - 1]) cylinder(r1 = boss_r - 1, r2 = boss_r, h = 1 + e);
}
}
// backrest bar channel (open towards the seat board)
translate([0, keel_back - 1, chan_floor]) {
stadium(bar_w + 2*bar_clear, bar_t + 2*bar_clear, bar_end_y + 2 - keel_back + 1);
translate([-(bar_w/2 + bar_clear), 0, bar_t/2]) cube([bar_w + 2*bar_clear, bar_end_y + 2 - keel_back + 1, 20]);
// slide path for the knob-side boss
translate([-boss_groove_w/2, 0, -groove_d]) cube([boss_groove_w, knob_y + boss_groove_w/2 - keel_back + 1, groove_d + 1]);
}
// M8 through-bolts in the walls, lock nut captive at the seat face
for (sx = [-1, 1]) translate([sx*bolt_x, bolt_y, 0]) {
translate([0, 0, keel_bot - 1]) cylinder(d = bolt_hole, h = -keel_bot + 2, $fn = 32);
translate([0, 0, -nut_h - 0.3]) rotate(30) cylinder(d = (nut_af + 0.3)/cos(30), h = nut_h + 1, $fn = 6);
}
// knob stud hole + recess
translate([0, knob_y, keel_bot - 1]) cylinder(d = knob_stud_d + 1, h = -keel_bot);
if (knob_cb_z > keel_bot) translate([0, knob_y, keel_bot - 1]) cylinder(d = knob_d + 4, h = knob_cb_z - keel_bot + 1);
// lever pocket (open to seat board and side) + pivot
mirror_x() {
translate([-9, cone_y - cav_hw, shoulder_top]) cube([30 + 9, 2*cav_hw, -shoulder_top + 1]);
translate([30, cone_y - cav_hw, shoulder_top - 2]) cube([edge_x + 20, 2*cav_hw, -shoulder_top + 3]);
// pivot slots, open to the seat face; keepers fill them above the pin
translate([pivot_x, cone_y - house_hw - 0.3, 0]) rotate([-90, 0, 0]) hull()
for (z = [-pivot_z, -1]) translate([0, z, 0]) cylinder(d = slot_w, h = 2*house_hw + 0.6, $fn = 32);
}
}
}
/* ---------- lever (profile in chair XZ plane, at rest) ---------- */
module lever_2d() {
difference() {
union() {
// tip arm, rests against the seat board
translate([-6, body_bot]) square([pivot_x + 6, -body_bot - 0.3]);
translate([-nub_w/2, nub_bot]) square([nub_w, body_bot - nub_bot + e]);
translate([pivot_x, pivot_z]) circle(r = hub_r);
// arm beyond pivot, kept low so it can rise
hull() {
translate([pivot_x, pivot_z]) circle(r = hub_r);
translate([edge_x + 2, -13.5]) circle(r = 5.5);
}
// handle
hull() { translate([edge_x + 2, -13.5]) circle(r = 5.5); translate([edge_x + 45, -handle_drop]) circle(r = 7); }
hull() { translate([edge_x + 45, -handle_drop]) circle(r = 7); translate([handle_end - 10, -handle_drop]) circle(r = 7); }
translate([handle_end - 10, -handle_drop]) scale([1.4, 1]) circle(r = 9);
}
translate([pivot_x, pivot_z]) circle(d = pin_d + 0.3, $fn = 32);
}
}
module lever() { linear_extrude(lever_w) lever_2d(); }
/* ---------- pivot pin (printed lying down, small flat on the bed) + 2 keepers ---------- */
module pivot() {
difference() {
translate([0, 0, pin_d/2 - 0.4]) rotate([0, 90, 0]) cylinder(d = pin_d, h = 2*house_hw, $fn = 48);
translate([-1, -pin_d, -pin_d]) cube([2*house_hw + 2, 2*pin_d, pin_d]);
}
for (i = [0, 1]) translate([i*12, pin_d + 4, 0]) cube([slot_w - 0.1, house_hw - cav_hw, keeper_h]);
}
/* ---------- socket fit gauge: same taper + stop ring, thin wall ---------- */
module gauge() {
difference() {
translate([0, 0, bore_bot]) cylinder(d = bore_d(bore_bot) + 8, h = shoulder_top - bore_bot);
translate([0, 0, bore_bot - e]) cylinder(d1 = bore_d(bore_bot), d2 = bore_d(shoulder_bot), h = shoulder_bot - bore_bot + e);
translate([0, 0, shoulder_bot - e]) cylinder(d = shoulder_hole, h = 10);
}
}
/* ---------- shims: fill the gap between the flat plate and the curved seat ---------- */
module shims() {
for (i = [0:3]) translate([(i % 2) * 26, floor(i / 2) * 26, 0])
difference() { cylinder(d = 22, h = seat_sag); translate([0, 0, -1]) cylinder(d = screw_d, h = seat_sag + 2); }
}
/* ---------- output ---------- */
if (part == "plate") rotate([180, 0, 0]) plate(); // seat face on the bed
else if (part == "lever") lever(); // lies flat
else if (part == "pivot") pivot();
else if (part == "shims") shims();
else if (part == "gauge") rotate([180, 0, 0]) translate([0, 0, -shoulder_top]) gauge();
else if (part == "assembly") {
plate();
mirror_x() translate([0, cone_y + lever_w/2, 0]) rotate([90, 0, 0]) color("orange") lever();
// context: seat board, backrest bar, gas cylinder
%translate([-200, -200, 0]) cube([400, 400, 15]);
%translate([0, keel_back - 60, chan_floor]) stadium(bar_w, bar_t, bar_end_y - keel_back + 60);
%translate([0, cone_y, cone_top_z - cone_round - cone_len])
cylinder(d1 = cone_d_bot, d2 = cone_d_top, h = cone_len);
}