Files
BartandClaude Opus 5.5 2edb878317 Printable seat plate for T-LoVendo AM-SOC26 office chair
Parametric OpenSCAD model with gas lift taper socket, backrest bar
channel with M8 through-bolts, lever with drop-in pivot, shims and a
taper fit gauge.

Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01QM7McqDDPqszyN8ojQxVjk
2026-10-31 23:42:26 +01:00

7.6 KiB
Raw Permalink Blame History

Office chair seat plate (3D printable)

A printable replacement for the seat mechanism plate of a T-LoVendo AM-SOC26 office chair (it arrived without one). The plate screws to the underside of the seat with the 4 original M6 screws, takes the gas lift taper, clamps the backrest bar with the original knob, and carries a lever that presses the gas lift release pin.

It is a single parametric OpenSCAD file: seat_plate.scad. Every dimension is a named parameter, so it can be adapted to similar chairs.

Assembly, seen from below

Underside Seat side
Plate from below Plate seat side

Safety. This replaces a steel part that you sit on. Printed plastic is weaker, creeps under constant load and can fail without much warning (especially PLA). Test it carefully (see Testing) and inspect it regularly for whitening, cracks or a growing gap at the back of the plate.

Parts

Export each part by setting part:

part What Qty Print orientation
plate The seat plate 1 Seat face down (already rotated)
lever Gas lift lever 1 Flat
pivot Lever pin (8 mm) + 2 keepers 1 set As exported (pin lies on a small flat)
shims 3 mm spacers for the curved seat 4 Flat
gauge Taper fit test piece 1 As exported, same settings as the plate
assembly Preview only – –
for p in plate lever pivot shims gauge; do
  openscad -o $p.stl -D "part=\"$p\"" seat_plate.scad
done

The STLs are not in this repo; generate them from the source.

Hardware

  • 4× M6×20 screws (the chair's originals) with 4× large M8 washers (23.7 mm OD, 8.5 mm ID, 2 mm thick) under the heads
  • 2× M8×35 socket head bolts, 2× M8 nylon lock nuts, 2× M8 washers (same washers as above)
  • Optional: an 8 mm steel rod cut to 30 mm instead of the printed pin

How it works

Gas lift socket

A 50 mm long tapered bore that matches the gas cylinder's taper (26.5 → 28 mm over 53 mm). Above it is a 3 mm stop ring with an 18 mm hole:

  • The release pin pokes through the hole into the lever pocket.
  • Normally there is a 1 mm gap between the cylinder top and the ring; the taper does all the gripping. The ring only catches the cylinder if the plate creeps further down the taper. This keeps the release pin at the height the lever expects and limits how far the taper can wedge into (and split) the boss.

Assemble the taper dry, without grease.

Backrest bar channel

The 35×16 mm stadium-section bar slides into a channel that is open towards the seat board. The bar's 23 mm flange (around the knob thread) presses against the seat board; the small 12.5 mm boss on the knob side runs in a slot in the channel floor. 76.5 mm of the bar is inside the channel (of the ~80 mm available before its ribbed cover).

This is the most heavily loaded part. Leaning back pushes the bar down on the rear edge of the channel and up against the seat board at its front end, a couple of roughly 3 kN in a hard lean. To make this stronger:

  • The channel walls are 20 mm thick, the floor 15 mm.
  • An M8 bolt runs vertically through each wall near the rear end. The lock nut sits in a hex pocket on the seat face (it can't turn and the seat board covers it); the bolt goes in from below with a washer under the head. This clamps the printed layers together where leaning back tries to pull them apart. With a 2 mm washer the bolt tip ends 0.8 mm below the seat face, so don't leave the washer out.

Section through the bar channel at the M8 bolts

Lever

A first-class lever: pulling the handle up pushes the inner end down onto the release pin. At rest the inner end lies against the seat board, 1.5 mm above the pin; nub travel is limited to 7.5 mm by the pocket floor.

Lever

The lever pivots on an 8 mm pin that drops into open-top slots in the housing walls. Pulling the handle pushes the pin up, so two printed keepers fill the slots above the pin ends; once the plate is mounted they are backed by the seat board.

Lever in its pocket Section through the pivot
Section in the lever plane Section through the pivot

Pivot pin and keepers

Seat screws

The seat underside is curved: about 3 mm higher at the screw holes than at the centre. The 4 printed shims fill that gap. The screw counterbores are 25 mm wide for the large washers, with 6 mm of plastic under them. Stack per screw: 2 mm washer + 6 mm plastic

  • 3 mm shim, which leaves about 9 mm of an M6×20 in the seat's T-nuts. Check that each screw goes in at least 8–9 turns by hand before tightening.

Calibrating the taper fit

Printed holes come out undersized, and this taper is shallow: every 0.1 mm of diameter moves the seating height by about 3.5 mm. Tune socket_clear with the gauge before printing the plate:

  1. Print gauge with exactly the settings, filament and orientation you'll use for the plate.
  2. Push it on the cylinder firmly by hand (twist it to get it off again).
  3. Target: about 3 mm of shiny taper visible below the gauge, and about 4 mm from the top of the gauge down to the cylinder top.
  4. If it sits X mm too high, increase socket_clear by roughly X / 35 mm. If it rattles or the cylinder touches the stop ring, decrease it.

Err slightly on the tight side: body weight seats it further, and the plate's thick boss stretches less than the thin gauge. Too loose means the cylinder rests on the stop ring and wobbles.

Here, socket_clear = 0.2 sat 15.5 mm high; the printed plate uses 0.5.

Printing

  • PLA works but is brittle and creeps. PETG, ABS/ASA (enclosure needed) or PA/PC are tougher choices.
  • Use many walls (8–10) so the channel walls print as solid perimeters, and a 100 % infill modifier around the bar channel. Print hot enough for good layer bonding.

Assembly

  1. Press the two M8 lock nuts into the hex pockets on the seat face.
  2. Insert the M8 bolts from below, with a washer under each head, and snug them up.
  3. Slide the pin through the lever, drop the lever into its pocket with the pin ends in the slots, and press the keepers in on top (a bit of tape holds them while flipping).
  4. Place the shims, put the plate on the seat and fit the M6×20 screws with the large washers.
  5. Tighten the M8 bolts, insert the backrest bar and fit the knob.
  6. Set the seat onto the gas cylinder (taper dry) and sit down to seat it.

Testing

Before trusting it, load the backrest gradually: put a bathroom scale between your hand and the top of the backrest and push to about twice your normal lean. Look and listen for whitening, creaking, or a gap opening at the back of the plate. Re-check the knob and the screws after the first days, since the plastic settles.

Known deviations on the printed chair

The measurements are hand measured. On the build in this repo:

  • One of the four outer screw holes had to be opened up about 1 mm with a drill (the hole pattern on the seat is probably not a perfect rectangle).
  • The hole for the backrest knob had to be drilled further back, so knob_from_rear_holes is too large for this chair.

The model has not been updated for these; measure your own chair and check the hole positions before printing.

Coordinates (for editing)

Origin at the centre of the 4-screw pattern on the seat underside, +y towards the front, +x to the sitter's right, z = 0 at the seat board; the plate hangs at z < 0. lever_side = -1 mirrors the lever to the left side.