Parametric OpenSCAD model with gas lift taper socket, backrest bar channel with M8 through-bolts, lever with drop-in pivot, shims and a taper fit gauge. Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com> Claude-Session: https://claude.ai/code/session_01QM7McqDDPqszyN8ojQxVjk
171 lines
7.6 KiB
Markdown
171 lines
7.6 KiB
Markdown
# Office chair seat plate (3D printable)
|
||
|
||
A printable replacement for the seat mechanism plate of a **T-LoVendo AM-SOC26** office
|
||
chair (it arrived without one). The plate screws to the underside of the seat with the
|
||
4 original M6 screws, takes the gas lift taper, clamps the backrest bar with the
|
||
original knob, and carries a lever that presses the gas lift release pin.
|
||
|
||
It is a single parametric [OpenSCAD](https://openscad.org) file: `seat_plate.scad`.
|
||
Every dimension is a named parameter, so it can be adapted to similar chairs.
|
||
|
||

|
||
|
||
| Underside | Seat side |
|
||
|---|---|
|
||
|  |  |
|
||
|
||
> **Safety.** This replaces a steel part that you sit on. Printed plastic is weaker,
|
||
> creeps under constant load and can fail without much warning (especially PLA).
|
||
> Test it carefully (see [Testing](#testing)) and inspect it regularly for whitening,
|
||
> cracks or a growing gap at the back of the plate.
|
||
|
||
## Parts
|
||
|
||
Export each part by setting `part`:
|
||
|
||
| `part` | What | Qty | Print orientation |
|
||
|---|---|---|---|
|
||
| `plate` | The seat plate | 1 | Seat face down (already rotated) |
|
||
| `lever` | Gas lift lever | 1 | Flat |
|
||
| `pivot` | Lever pin (8 mm) + 2 keepers | 1 set | As exported (pin lies on a small flat) |
|
||
| `shims` | 3 mm spacers for the curved seat | 4 | Flat |
|
||
| `gauge` | Taper fit test piece | 1 | As exported, same settings as the plate |
|
||
| `assembly` | Preview only | – | – |
|
||
|
||
```sh
|
||
for p in plate lever pivot shims gauge; do
|
||
openscad -o $p.stl -D "part=\"$p\"" seat_plate.scad
|
||
done
|
||
```
|
||
|
||
The STLs are not in this repo; generate them from the source.
|
||
|
||
### Hardware
|
||
|
||
- 4× M6×20 screws (the chair's originals) with 4× large M8 washers
|
||
(23.7 mm OD, 8.5 mm ID, 2 mm thick) under the heads
|
||
- 2× M8×35 socket head bolts, 2× M8 nylon lock nuts, 2× M8 washers (same washers as above)
|
||
- Optional: an 8 mm steel rod cut to 30 mm instead of the printed pin
|
||
|
||
## How it works
|
||
|
||
### Gas lift socket
|
||
|
||
A 50 mm long tapered bore that matches the gas cylinder's taper
|
||
(26.5 → 28 mm over 53 mm). Above it is a 3 mm **stop ring** with an 18 mm hole:
|
||
|
||
- The release pin pokes through the hole into the lever pocket.
|
||
- Normally there is a 1 mm gap between the cylinder top and the ring; the taper does
|
||
all the gripping. The ring only catches the cylinder if the plate creeps further down
|
||
the taper. This keeps the release pin at the height the lever expects and limits how
|
||
far the taper can wedge into (and split) the boss.
|
||
|
||
Assemble the taper **dry**, without grease.
|
||
|
||
### Backrest bar channel
|
||
|
||
The 35×16 mm stadium-section bar slides into a channel that is open towards the seat
|
||
board. The bar's 23 mm flange (around the knob thread) presses against the seat board;
|
||
the small 12.5 mm boss on the knob side runs in a slot in the channel floor. 76.5 mm
|
||
of the bar is inside the channel (of the ~80 mm available before its ribbed cover).
|
||
|
||
This is the most heavily loaded part. Leaning back pushes the bar down on the rear
|
||
edge of the channel and up against the seat board at its front end, a couple of
|
||
roughly 3 kN in a hard lean. To make this stronger:
|
||
|
||
- The channel walls are 20 mm thick, the floor 15 mm.
|
||
- An **M8 bolt runs vertically through each wall** near the rear end. The lock nut sits
|
||
in a hex pocket on the seat face (it can't turn and the seat board covers it); the
|
||
bolt goes in from below with a washer under the head. This clamps the printed layers
|
||
together where leaning back tries to pull them apart. With a 2 mm washer the bolt tip
|
||
ends 0.8 mm below the seat face, so **don't leave the washer out**.
|
||
|
||

|
||
|
||
### Lever
|
||
|
||
A first-class lever: pulling the handle up pushes the inner end down onto the
|
||
release pin. At rest the inner end lies against the seat board, 1.5 mm above the pin;
|
||
nub travel is limited to 7.5 mm by the pocket floor.
|
||
|
||

|
||
|
||
The lever pivots on an 8 mm pin that drops into **open-top slots** in the housing walls.
|
||
Pulling the handle pushes the pin *up*, so two printed **keepers** fill the slots above
|
||
the pin ends; once the plate is mounted they are backed by the seat board.
|
||
|
||
| Lever in its pocket | Section through the pivot |
|
||
|---|---|
|
||
|  |  |
|
||
|
||

|
||
|
||
### Seat screws
|
||
|
||
The seat underside is curved: about 3 mm higher at the screw holes than at the centre.
|
||
The 4 printed shims fill that gap. The screw counterbores are 25 mm wide for the large
|
||
washers, with 6 mm of plastic under them. Stack per screw: 2 mm washer + 6 mm plastic
|
||
+ 3 mm shim, which leaves about 9 mm of an M6×20 in the seat's T-nuts. Check that each
|
||
screw goes in at least 8–9 turns by hand before tightening.
|
||
|
||
## Calibrating the taper fit
|
||
|
||
Printed holes come out undersized, and this taper is shallow: **every 0.1 mm of
|
||
diameter moves the seating height by about 3.5 mm**. Tune `socket_clear` with the gauge
|
||
before printing the plate:
|
||
|
||
1. Print `gauge` with exactly the settings, filament and orientation you'll use for the plate.
|
||
2. Push it on the cylinder firmly by hand (twist it to get it off again).
|
||
3. Target: about 3 mm of shiny taper visible below the gauge, and about 4 mm from the top
|
||
of the gauge down to the cylinder top.
|
||
4. If it sits X mm too high, increase `socket_clear` by roughly X / 35 mm. If it
|
||
rattles or the cylinder touches the stop ring, decrease it.
|
||
|
||
Err slightly on the tight side: body weight seats it further, and the plate's thick
|
||
boss stretches less than the thin gauge. Too loose means the cylinder rests on the
|
||
stop ring and wobbles.
|
||
|
||
Here, `socket_clear = 0.2` sat 15.5 mm high; the printed plate uses **0.5**.
|
||
|
||
## Printing
|
||
|
||
- PLA works but is brittle and creeps. PETG, ABS/ASA (enclosure needed) or PA/PC are
|
||
tougher choices.
|
||
- Use many walls (8–10) so the channel walls print as solid perimeters, and a 100 %
|
||
infill modifier around the bar channel. Print hot enough for good layer bonding.
|
||
|
||
## Assembly
|
||
|
||
1. Press the two M8 lock nuts into the hex pockets on the seat face.
|
||
2. Insert the M8 bolts from below, with a washer under each head, and snug them up.
|
||
3. Slide the pin through the lever, drop the lever into its pocket with the pin ends in
|
||
the slots, and press the keepers in on top (a bit of tape holds them while flipping).
|
||
4. Place the shims, put the plate on the seat and fit the M6×20 screws with the large washers.
|
||
5. Tighten the M8 bolts, insert the backrest bar and fit the knob.
|
||
6. Set the seat onto the gas cylinder (taper dry) and sit down to seat it.
|
||
|
||
## Testing
|
||
|
||
Before trusting it, load the backrest gradually: put a bathroom scale between your hand
|
||
and the top of the backrest and push to about twice your normal lean. Look and listen
|
||
for whitening, creaking, or a gap opening at the back of the plate. Re-check the knob
|
||
and the screws after the first days, since the plastic settles.
|
||
|
||
## Known deviations on the printed chair
|
||
|
||
The measurements are hand measured. On the build in this repo:
|
||
|
||
- One of the four outer screw holes had to be opened up about 1 mm with a drill (the hole
|
||
pattern on the seat is probably not a perfect rectangle).
|
||
- The hole for the backrest knob had to be drilled further back, so `knob_from_rear_holes`
|
||
is too large for this chair.
|
||
|
||
The model has **not** been updated for these; measure your own chair and check the hole
|
||
positions before printing.
|
||
|
||
## Coordinates (for editing)
|
||
|
||
Origin at the centre of the 4-screw pattern on the seat underside, +y towards the front,
|
||
+x to the sitter's right, z = 0 at the seat board; the plate hangs at z < 0.
|
||
`lever_side = -1` mirrors the lever to the left side.
|